DeWalt BDDC180 Handleiding (3 Pagina's) (2024)

Important Safety Instructions

SAVE THESE INSTRUCTIONS. This manual contains important safety and operating

instructions for the battery charger. Catalog # BDDC140, BDDC180

Before using charger, read and understand all instructions and cautionary markings on (1)

charger, (2) battery pack, and (3) product using battery pack.

DANGER: 120 volts present at charging terminals. Do not probe with conductive objects.

Danger of electric shock or electrocution.

DANGER: If battery pack case is cracked or damaged, do not insert into charger. Danger of

electric shock or electrocution.

DANGER: Never attempt to open the battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service center for recycling.

WARNING: Don’t allow any liquid to get inside charger. Electric shock may result.

CAUTION: To reduce risk of injury, charge only Black & Decker rechargeable batteries.

Other types of batteries may burst, causing personal injury and damage.

To facilitate the cooling of the battery pack after use, avoid placing the charger or battery

pack in a warm environment such as in a metal shed, or an uninsulated trailer.

Do not expose charger to rain or snow.

Use of an attachment not recommended or sold by Black & Decker may result in risk of

fire, electric shock, or injury to persons.

This charger is not intended for any uses other than charging Black & Decker rechargeable

batteries. Any other uses may result in risk of fire, electric shock or electrocution.

To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in risk of fire, electric shock, or electrocution. If an extension

cord must be used, make sure:

That the pins on plug of extension cord are the same number, size and shape of those

of plug on charger.

That extension cord is properly wired and in good electrical condition and the wire size

is large enough for AC ampere rating of charger as specified below.

An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety.

The smaller the gauge number of the wire, the greater the capacity of the cable, that is, 16

gauge has more capacity than 18 gauge. When using more than one extension to make up

the total length, be sure each individual extension contains at least the minimum wire size.

RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS

Total Extension Cord Length (feet)

25 50 75 100 125 150 175

Wire Gauge

18 18 16 16 14 14 12

The charger is ventilated through slots in the housing. Do not place any object on top of

charger or place the charger on a soft surface that might block the ventilation slots and result

in excessive internal heat. Place the charger in a position away from any heat source.

Do not operate charger with damaged cord or plug have them replaced immediately.

Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged

in any way; take it to an authorized service center.

Do not disassemble charger; take it to an authorized service center when service or repair is

required. Incorrect reassembly may result in risk of electric shock, electrocution or fire.

The charger is designed to operate on standard120 VAC, 60Hz household electrical power.

Do not attempt to use it on any other voltage.

To reduce risk of electric shock, unplug charger from outlet before attempting any cleaning.

Removing the battery pack will not reduce this risk.

NEVER attempt to connect 2 chargers together.

DO NOT store or use the tool and battery pack in locations where the temperature may reach

or exceed 105°F (such as outside sheds or metal buildings in summer).

A small leakage of liquid from the battery cells may occur under extreme usage, charging

or temperature conditions. This does not indicate a failure. However, if the outer seal is

broken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10

minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a

25-35% solution of potassium hydroxide.

SAVE THESE INSTRUCTIONS

Introduction

READ AND UNDERSTAND ALL OF THE INSTRUCTIONS IN THIS MANUAL BEFORE

ATTEMPTING TO CHARGE THE BATTERY PACK FOR YOUR TOOL.

Your charger is designed to use standard 120 volt AC, 60 Hz power. Do not use DC or any

other voltage. Charge time is 3 to 6 hours depending on battery pack type and condition.

Charging Procedure

1. Plug the charger into an appropriate outlet.

2. Insert 1 or 2 batteries into the charger (Figure 1).

NOTE: Charge time is the same for multiple batteries.

Be sure the battery is fully seated in the charger. The red

“Charging Indicator” light will come on indicating that there is

contact between the battery and charger. The light will stay on

as long as the battery is in the charger and the charger is

plugged into a working outlet. It WILL NOT flash, go out or

change to a different color when the charging cycle is complete.

Leaving the Battery Pack in the Charger

The charger and battery pack can be left connected with the red light glowing indefinitely. The

charger will keep the battery pack fresh and fully charged.

NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery

pack has not been kept on maintenance charge, it may need to be recharged before use. A

battery pack may also slowly lose its charge if left in a charger that is not plugged into an

appropriate AC source.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when

the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery

pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is

important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a

normal condition, and does not indicate a problem.

3. If the battery pack does not charge properly — (1) Check power at receptacle by plugging

in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights. (3) Move charger and battery pack to a

location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C).

(4) If charging problems persist, take or send the tool, battery pack and charger to your

local service center.

4. The battery pack should be recharged when it does not produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE use under these conditions.

Follow the charging procedures. You may also charge a partially used pack whenever you

desire with no adverse affect on the battery pack.

5. Black & Decker battery packs that are labeled “NiMH” should only be used with chargers

labeled “NiMH“ or “NiCd/NiMH.”

6. Under certain conditions, with the charger plugged into the power supply, the exposed

charging contacts inside the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or

any buildup of metallic particles should be kept away from charger cavities. Always unplug

the charger from the power supply when there is no battery pack in the cavity. Unplug

charger before attempting to clean.

7. Do not immerse charger in water or any other liquid.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation)

Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to

recycle the battery (or battery pack) at the end of its useful life have already been

paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium

batteries in the trash or municipal solid waste stream and the RBRC program provides an

environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established programs

in the United States and Canada to facilitate the collection of spent nickel-cadmium batteries.

Help protect our environment and conserve natural resources by returning the spent

nickel-cadmium battery to an authorized Black & Decker service center or to your local retailer

for recycling. You may also contact your local recycling center for information on where to drop

off the spent battery, or call 1-800-8-BATTERY.

Maintenance

Use only mild soap and damp cloth to clean the charger. Never let any liquid get inside the

charger; never immerse any part of the charger into a liquid.

Important

This product is not user serviceable. There are no user serviceable parts inside the charger.

Servicing at an authorized service center is required to avoid damage to static sensitive

internal components.

READ ALL OF THE INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO

CHARGE THE BATTERY PACK FOR YOUR TOOL.

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be

performed by certified service centers or other qualified service organizations, always using

identical replacement parts.

Service Information

Black & Decker offers a full network of company-owned and authorized service locations

throughout North America. All Black & Decker Service Centers are staffed with trained

personnel to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair, or genuine factory replacement parts, contact the

Black & Decker location nearest you.

To find your local service location, refer to the yellow page directory under "Tools–Electric" or

call: 1-800-54-HOW TO (544-6986).

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material

or workmanship. The defective product will be replaced or repaired at no charge in either of

two ways:

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should be

made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after

the sale). Proof of purchase may be required. Please check with the retailer for their specific

return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may be

required. Black & Decker owned and authorized service centers are listed under

"Tools–Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any

questions, contact the manager of your nearest Black & Decker Service Center. This

product is not intended for commercial use

Free Warning Label Replacement: If your warning labels become illegible or are missing,

call 1-800-544-6986 for a free replacement.

VEA EL ESPAÑOL EN LA

CONTRAPORTADA.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

LIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

INSTRUCTION MANUAL

D

D

D

D

D

D

D

D

D

DU

U

U

U

U

U

U

U

U

UA

A

A

A

A

A

A

A

A

AL

L

L

L

L

L

L

L

L

LC

C

C

C

C

C

C

C

C

CH

H

H

H

H

H

H

H

H

HA

A

A

A

A

A

A

A

A

AR

R

R

R

R

R

R

R

R

RG

G

G

G

G

G

G

G

G

GE

E

E

E

E

E

E

E

E

ER

R

R

R

R

R

R

R

R

R

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-54-HOW-TO (544-6986)

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-54-HOW-TO (544-6986)

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE

No., AND DATE CODE (e.g. 0130M). IN MOST CASES, A BLACK & DECKER REPRESENTATIVE

CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR

COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

Fig.1

See ‘Tools-Electric’

Yellow Pages

for Service & Sales

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Catalog Nos. BDDC140, BDDC180

CAT. NO. BDDC140, BDDC180 FORM NO. 5101327-01(JUN 04) COPYRIGHT © 2004 BLACK & DECKER PRINTED IN CHINA

DeWalt BDDC180 Handleiding (3 Pagina's) (2024)
Top Articles
Latest Posts
Article information

Author: Greg Kuvalis

Last Updated:

Views: 6348

Rating: 4.4 / 5 (55 voted)

Reviews: 86% of readers found this page helpful

Author information

Name: Greg Kuvalis

Birthday: 1996-12-20

Address: 53157 Trantow Inlet, Townemouth, FL 92564-0267

Phone: +68218650356656

Job: IT Representative

Hobby: Knitting, Amateur radio, Skiing, Running, Mountain biking, Slacklining, Electronics

Introduction: My name is Greg Kuvalis, I am a witty, spotless, beautiful, charming, delightful, thankful, beautiful person who loves writing and wants to share my knowledge and understanding with you.